Menu
Your Cart

External Wall Insulation Systems

Heat moves from warmer to colder areas. Therefore, on cold days, heat from inside a building seeks to get outside. And on warmer days, the heat from outside the building seeks to get inside. Insulating the external walls would slow the movement of heat out through the walls thereby dramatically reducing heating demand. 

Most buildings in UK are constructed with solid walls. They dont have cavities that can be filled or injected with insulation. These solid external walls need to be insulated by adding a layer of insulation to either to the interior face or to the exterior face of the wall. The best method is to insulate the walls on its exterior face. The savings on your heating bills will be bigger, and those savings would have a great impact on your budget.

In a typical building, around 40% of the energy used to heat or cool a room is wasted due to poorly insulated external walls. Correctly chosen external wall insulation (EWI) systems dramatically cut energy loss by wrapping the building in a thermally resistant envelope and also provide lasting protection for the entire structure of the building. The external wall insulation system involves an entire set of different products and accessories, so it is important to make sure that you get all quality products you need from one place. Here at Insulation Shop we provide just that  a complete set of high quality insulation products and all necessary accessories for insulating your exterior walls. The best possible building performance can only be realised if walls are externally insulated.

Benefits of EWI Systems
  • External wall is warm and dry, increasing thermal performance and reducing building maintenance,
  • The heat retention capability of the existing wall is fully utilised,
  • Removes of cold bridges reducing the risk of condensation, damp and mould,
  • Eliminates cracking caused by thermal expansion and contraction,
  • Lightweight construction methods can be used, allowing for fast installation,
  • Reduces heating costs by up to 40%,
  • Reduces maintenance costs,
  • Improves the living environment: - Warmer in Winter - Cool in Summer
  • Protects the building fabric and enhances the aesthetics,
  • Does not encroach on living space,
  • May increase the value of your property

External Wall Insulation (EWI) is a system, which not only insulates, but also protects the exterior of your home. External wall insulation involves fixing a layer of insulation material to the wall, then covering it with a special type of render or cladding. This finish can be smooth, textured, painted, tiled, brick slipped, dry-dashed or panelled.

The usual EWI system consists of insulation, adhesive render or base coat, insulation fixings, polypropylene or glass fibre mesh, primers, decorative surface finishes and also beads, trims and flashings.

  • The insulation is the main thermal layer, and also the background for applying the adhesive render, basecoat and finishes to. Various types of insulation are available The choice of the insulation is dependant on the required thermal performance, zoning, location and cost. The rigid or semi rigid insulation boards are fixed either directly with adhesive, with insulation fixings, or a combination of both.
  • Adhesive renders are applied to the rear of the board in either a dot and dab method, with the perimeter of the board being coated and two slobs in the middle, or with a serrated edge trowel to the entire rear of the insulation board.
  • Insulation fixings used in most EWI systems. These are specified to suit the existing substrate, the height and shape of the building, its location and elevation, and proximity to other buildings. Most times, a combination of adhesive render and insulation fixings are used. 
  • Most basecoats used are polymer modified cement based renders, which are weatherproof and can accommodate varying degrees of thermal movement. Basecoats are reinforced with a mesh over the top of the insulation layer. The reinforcement layer would spread stresses across the facade surface into the insulation below, provide impact resistance to the system and enhance weatherproofing.
  • The final decorative surface finish would provide added weather proofing properties to the building envelope. This finish can be smooth, textured, painted, tiled, brick slipped, dry-dashed, wet-dashed or panelled. It cold be acrylic textures, silicone textures, mosaic textures, mineral renders and brick effect renders.
  • All EWI systems require the use of beads, trims and flashings. They are used as starters, junctions and closers.
Types of Insulation for EWI systems

  • Expanded polystyrene (EPS) White & Grey,
  • Extruded polystyrene (XPS),
  • Phenolic, 
  • Glass wool and Mineral (Stone) wool, 
  • Polyisocyanurate (PIR)

Expanded Polystyrene (EPS) White & Grey Installation

Expanded Polystyrene (EPS) is a lightweight, rigid, plastic foam insulation material, which a cost effective, easy-to-use product for EWI applications. The structure of EPS consists of 98% air. Its initial thermal properties are maintained throughout its working life. It is non-toxic, moisture resistant and rot proof.

Grey Polystyrene (Graphite) is a high quality expanded polystyrene (EPS) board enhanced with integrated graphite within its bead structure. The high-purity graphite particles integrated within the insulation beads reflects radiant heat and significantly improves insulation capability, providing up to 20% greater r-value than traditional white EPS of the same thickness. Warm air always moves towards cold air, In Grey Polystyrene (Graphite) the path taken by warm air moving towards the cold air takes many twists and turns along the way, slowing down the heat transfer, keeping the premises warmer.

Benefits
  • Cost effective - cheapest insulation material in the market. 
  • Easy to cut using a fine tooth saw or hot wire cutter,
  • The surface can be rasped on site to remove level differences,
  • Durable, not affected by short exposure to UV or rain.
  • Long term exposure can cause slight discolouration, but does not affect the thermal performance,
  • Has a high K-value when compared with other insulations,
  • Can be used in low rise and high Rise applications and in coastal locations,
  • Does not absorb moisture and its thermal and mechanical properties are unaffected by damp, humidity or moisture,
  • 100% recyclable.
Precautions
  • Should be kept away from solvents, 
  • Should not be exposed to naked flame,
  • Classified as combustible (combustibility is limited due to retardants present),
  • Should be stored in protected packaging and away from direct sunlight.

Extruded Polystyrene (XPS) Installation

XPS is a closed cell extruded polystyrene insulation with good thermal and water resisting properties having a high compressive strength. A wide range of thicknesses are available to achieve the thermal values required. Extruded polystyrene can withstand extreme loads. Used mainly below ground applications.

Benefits
  • Able to withstand extreme loads, 
  • Below ground applications,
  • Easy to cut using a fine tooth saw or hot wire cutter,
  • Highly water resistant,
  • Can be stored and installed in severe wet weather conditions with no deterioration during its life,
  • Durable, not affected by short exposure to UV or rain.
  • Has a high K-value when compared with other insulations,
  • Can be used in low rise and high Rise applications and in coastal locations,
  • Does not absorb moisture and its thermal and mechanical properties are unaffected by damp, humidity or moisture,
  • 100% recyclable.
Precautions
  • Should be kept away from solvents, 
  • Should not be exposed to naked flame,
  • Classified as combustible (combustibility is limited due to retardants present),
  • Can react to PVC cables and cause cables to become brittle, therefore a conduit should  be used.

Phenolic Insulation

Rigid phenolic insulation is produced by mixing high solids and phenolic resin with a surface acting agent. The heat created by the reaction evaporates a volatile liquid blowing agent in the mixture which produces a network of small bubbles in the material. This insulating core is bonded to two flexible tissue faced layers. The rigid phenolic insulation offer very good thermal insulating properties due to the very low thermal conductivity of phenolic foam. It can actually be 50% more effective than other common insulation materials. Its low thermal conductivity allows specified thermal performance targets to be achieved with minimal thickness of insulation, and saves space.

Kingspan Kooltherm K5 External Wall Board is a one of the top selling phenolic core external wall insulation boards, applicable to both solid and cavity brick and block walls.Kingspan Kooltherm K15 Rainscreen Board is specially created board to be used as a rainscreen in most frame buildings. Xtratherm Safe-R is another phenolic rigid EWI board available at the Insulation Shop.

Benefits
  • Offers the best K-value of all the available insulation - thinner boards required,
  • Easy to cut using a fine tooth saw,
  • High closed cell content and fine cell structure,
  • Lightweight, easy to transport , handle and install,
  • Resistant to fungus and mould growth and will not sustain vermin,
  • Highly resistant to moisture penetration,
  • Dimensionally stable and can be cut accurately to achieve a snug fit,
  • Self extinguishing, low smoke emission, 
  • Can be used in low rise and high Rise applications and in coastal locations.
Precautions
  • Should be kept dry, 
  • Should not be used if effected by rain until it has been dried out,
  • Should not be exposed to naked flame,
  • Should not be left exposed for long periods of time to direct sunlight and rain, 
  • Classified as combustible (combustibility is limited due to retardants present),

Mineral Fibre - Glass wool, Rock wool Insulation

Glass mineral wool is made from sand and recycled glass, limestone and soda ash. The glass is spun to form millions of fine fibres. A resin is used to bind the long fibres together to form a mat of material giving good tear strength. The density of the product determines whether the insulation is a lightweight quilt supplied in rolls, a flexible slab or a rigid slab, and its thermal insulation value.

Rock wool (also known as mineral wool or stone wool) is manufactured from molten rock in a furnace through which a stream of air or steam is blown at temperature of about 1600 C. The final product creates a mass of fine, intertwined fibres which may contain binder (often food grade starch) and an oil to reduce dusting. When pressed into rolls and sheets their ability to partition air makes them excellent heat insulators and sound absorbers. The insulation is produced in a variety of densities according to format and function. High quality Rockwool Fasrock-LL External Wall Insulation Slab and Rockwool Frontrock MAX E Dual Density External Wall Insulation Slab are available at Insulation Shop.

Benefits
  • The only insulation to be classed as non-combustible,
  • Offers good K-values,
  • Production emissions within UK legal defined limits,
  • Reduces overall environmental impact and formaldehyde-free,
  • Non skin irritant,
  • Easy to handle and work,
  • Resistant to rot,
  • Excellent acoustic and thermal properties,
  • Recyclable, 
  • Can be used in low rise and high Rise applications and in coastal locations.

Precautions
  • Should be stored on a flat, covered, protected surface, 
  • Should be kept dry, 
  • Should not be left exposed for long periods of time to rain,
  • Should not be used if effected by rain until it has been dried out,
  • Should limit the area of application of the boards and to basecoat at the earliest chance to avoid the boards becoming wet.

Polyisocyanurate (PIR) Insulation

Polyisocyanurate (PIR) insulation is a closed-cell rigid foam board manufactured with isocyanate and polyether mixed together in the presence of a catalyst that allows the molecules to rearrange, forming closed cells. It has a wider operating temperature range that surpasses standard polystyrene and is fire and smoke resistant. PIR insulation is available as a sprayed foam and as a rigid foam board. PIR does not require a thermal moisture barrier prior to installation. Celotex SW3000 is a PIR EWI board available at Insulation Shop, but would be sold at minimum run of 600m2.

Benefits
  • Offers the best K-value of all the available insulation - thinner boards required,
  • Easy to cut using a fine tooth saw,
  • High closed cell content and fine cell structure,
  • Lightweight, easy to transport , handle and install,
  • Resistant to fungus and mould growth and will not sustain vermin,
  • Highly resistant to moisture penetration,
  • Dimensionally stable and can be cut accurately to achieve a snug fit,
  • Can be used in low rise and high Rise applications and in coastal locations.
Precautions
  • Should not be exposed to naked flame.
  • Should be kept dry, 
  • Should not be used if effected by rain until it has been dried out,
  • Should not be left exposed for long periods of time to direct sunlight and rain, 
  • Classified as combustible (combustibility is limited due to retardants present),
Types of Render

  • Acrylic renders
  • Mineral renders
  • Mosaic renders
  • Silicone renders

Acrylic render

Acrylic render is a finishing coat for render, containing acrylic aggregates to display an attractive finish. It is much more resistant to cracking than other types of render. Acrylic render is available in a wide range of colours and textures ranging from 1mm to 3mm aggregate size.Acrylic render is also fast drying, taking only two days to cure and dry while traditional renders can take up to 28 days. Acrylic render can be used to cover up small hairline cracks in masonry surfaces. The minute reinforcing fibres in Acrylic renders produce an incredibly tough and durable finish. It is permeable to water vapours and allows the substrates (brick etc) to breathe. It is also resistant to efflorescence (the white salts that sometimes leak from brickwork). Acrylic render can be trowelled on or rolled or even sprayed onto a surface. Two coats are generally applied.

Benefits
  • Easy to apply,
  • Easy to clean,
  • Lasts longer - about 8 years,
  • Covers hairline cracks,
  • Water vapour permeable,
  • Allows substrates to breathe,
  • Resistant to efflorescence,
  • Resisting driving rain,
  • Resists UV,
  • Can be trowelled on or rolled or even sprayed,
  • Available in a wide range of colours and textures.
Precautions
  • Should be cleaned of fallen leaves  - might grow algae

Mineral render

Mineral Render is eco-friendly, manufactured from natural materials such as mineral aggregates, and white marble grain. It is available with a rolled texture in 2, 3 and 4mm grain sizes. Mineral Render is highly damage resistant and also is Class 0 surface spread of flame. Mineral render contains cement contact allowing the product to set quicker, so it can be easily used during lower temperature periods. 

Benefits
  • Easy to apply,
  • Easy to clean,
  • Highly damage resistant,
  • Covers hairline cracks,
  • Sets quickly - contains cement,
  • Can be used during lower temperature periods,
  • Fire resistant,
  • Allows substrates to breathe,
  • Resisting driving rain,
  • Resists UV,
  • Available in a wide range of colours and textures,
  • Made entirely from natural materials.

Mosaic render

Flexible and easy to clean render with increased scratch resistance and covering ability. Suitable for indoor and outdoor use on walls exposed to high wear: at plinths, entrances, hallways, window and door reveals. Sealing component: transparent resins. Filler: coloured quartz stone. Can be applied and smoothed with stainless steel trowels. Produces a glassy, colourful coat upon setting. Mosaic render can be used on concrete substrates and traditional plasters etc. 

Benefits
  • Easy to apply and clean,
  • Can be applied and smoothed with stainless steel trowels,
  • Increased scratch resistance, 
  • Covers hairline cracks,
  • Sets quickly - contains cement,
  • Can be used during lower temperature periods,
  • Fire resistant,
  • Allows substrates to breathe,
  • Resisting driving rain,
  • Resists UV,
  • Available in a wide range of colours and textures.

    Precautions
    • Might collect dirt

    Silicone render (Polymer render)

    Polymer render is a cement based system with specially selected polymers added to the mix. These polymers make the finished coat strong yet flexible, allowing them to be used on any substrate. Polymer renders incorporate silicone water repellents as an integral part of the cement based render system. This silicone technology allow water vapour to pass through the render, letting the substrate breathe. The use of nylon reinforced base coats provides a high strength base for the finish coat. Polymer render is available as one coat render, eliminating the need for a base coat. Polymer renders come in a wide range of colours and can be finished in different textures, from a flat sponged float finish or a rougher scraped finish as well as Pebble Dash. They are usually premixed and only require the addition of clean water to produce the final product. This ensures the quality of the render remains consistent and ensures a superior finish.

    Benefits
    • Tough cement based render,
    • Can be applied on a range of substrates,
    • Increased scratch resistance, 
    • Covers hairline cracks,
    • Allows substrates to breathe,
    • Textures could be smooth or dry or wet dashed,
    • Fire resistant,
    • Available premixed,,
    • Resisting driving rain,
    • Resists UV.

      Precautions
      • Might collect dirt

      Installation of EWI Systems

      To correctly specify which insulation system to use, the existing wall envelope should be examined.

      • Check the walls for any visual defects,
      • Check for rising damp and its causes,
      • Check for existing movement joints,
      • Carry out a line and level survey to determine if a levelling coat is required,
      • Check for efflorescence (the white salts that sometimes leak from brickwork),
      • Check the need for repositioning of,  temporary removal or extension of services such as electricity, gas, telephone, TV or internet.
      • Also, check if building permission is required.

      The drawings and specification would include,

      Installation

      • The wall should be cleaned from dirt, grime, algae etc, and be allowed to fully dry out, 
      • If a building has an existing rendered finish, and If the render is in a poor condition--by trapping water, transmitting damp, and not allowing the existing building to breathe, then it is better to remove the render,
      • Check the line and level of any existing building, and the uneven surface of the wall should be corrected,
      • Carry out a pull-out test for adhesives and insulation fixings,  
      • EWI boards should be protected from adverse weather, direct sunlight and possible impact damage,
      • Insulation work should only done in dry conditions, 
      • Boards should be laid in a staggered pattern,
      • They should be staggered at the edges of buildings so that they form a toothed finish,  
      • The boards should be cut in an L shape around the corners of openings,
      • No small cuts of boards are allowed be used, 
      • Gaps between boards should be limited, and if that happens the gaps should be filled tight fit with the same type of insulation,
      • Boards should be level so that the basecoat and decorative finish are installed on a flat surface,
      • Beads and trims to be fixed at given locations, starter tracks at the beginning, beads and trims as the work progresses,
      • Adhesive renders should be applied to the rear of the board, and should follow either a dot and dab method to the board edges, or a fully applied adhesive using a serrated trowel,
      • Mechanical anchors, insulation fixings should be used as per specification,
      • Insulation fixings should be installed at 90 degrees from the wall face, and the washer head sitting flush with the insulation board face,
      • Application of basecoat should only be carried out when the weather is fine and free from rain,
      • In a thin basecoat system, the application of any mesh should occur at the first basecoat stage,
      • Meshes for the thick basecoat system are generally metal laths types and are fixed to the insulation prior to first base coat,
      • Meshes should be installed into the wet basecoat, using the back of a steel trowel and pushed in, so that they sit in the top third,
      • Meshes should be continuous, and should have a minimum 100mm lap with the adjacent mesh to ensure strength and continuity of the basecoat,
      • Once the basecoat has been applied, it should be left to cure to receive the final finish,
      • Finishes should only be applied in good weather and within ambient temperatures (5-30 C), 
      • Finishes should be stored in areas that can achieve a constant temperature, and should not drop below 5C,
      • Textured finishes should be applied with a steel trowel and rubbed with a plastic or nylon trowel to reveal the aggregate,
      • Junctions are finished with a mastic sealant, however its use should be kept to a minimum as they have a short life cycle and will need to be maintained at regular intervals,
      • General good practice would be to fill the gap with the silicone sealant and the final finish taken over the top.

      Typical installation examples

      EWI Cladding systems

      • The actual method of installation will depend on the chosen cladding system.
      • External expanded polystyrene should be cut to ensure a tight fit between the battens and should be wedged into position.
      • If there is an an air gap between the insulation and the cladding, the EPS external boards should be pinned in place using corrosion-free fixings. 
      • A breathable sarking felt should be placed over the insulation, and the edges and joints sealed.
      • As the use of a single layer of EPS external insulation fitted between standard 38-50mm battens will not provide a U-value which satisfies the Building Regulations, a second layer of EPS external board should be fixed over the battens.
      • The cladding system should be efficiently fixed back to the main wall to prevent vertical downward drag of cladding in accordance with the cladding manufacturers instructions.

      Cladding is a non-load bearing skin attached to the outside of a home to shed water and protect the building from the effects of weather and also the key element in the aesthetic appeal of the building. It also directly influences both building cost and property value. The embodied energy, resource depletion and recyclability of the cladding must be balanced against maintenance and durability appropriate to life span. The roles of cladding include sound and thermal insulation, fire resistance and easy cleaning.

      Cladding is typically made from wood, metal, vinyl, masonry and a range of composite materials. Cladding systems include horizontal or vertical boards, overlapping panels or smaller panels such as shingles and tiles. It can be attached directly to the frame or to an intermediate layer of spacers. Cladding is generally considered as non-load bearing, however, some sheet cladding systems can have a structural role when fixed to the frame such as fibre reinforced cement sheeting, reconstituted composite timber, structural plywood. 

      R-value Comparison Chart for External Wall Insulation available at Insulation Shop

      Legend 

      1* Rockwool Frontrock Max-E External Wall Insulation Slab

      2* Rockwool Fasrock-LL External Wall Insulation Slab

      3* Kingspan Kooltherm K15 Rainscreen Board

      4* Xtratherm Safe-R Insulation Board

      5* Kingspan Kooltherm K5 External Board

      6* Grey Polystyrene (Graphite) EPS Board

      7* Cellecta Hexatherm XPeri Perimeter Wall Insulation Board, Sundolitt XPS300 Extruded Polystyrene Board

      8* Cellecta Hexatherm XPeri Perimeter wall Insulation Board

      9* Jablite EPS100 Polystyrene Insulation Board

      10* Kay-Metzeller EPS70 Polystyrene Insulation Board

      11* Jablite EPS70 Polystyrene Insulation Board, Jablite External Wall Polystyrene Insulation Board

      12* White Polystyrene Boad EPS

      CHOOSE MANUFACTURERS or scroll down to see products (show)

      Brand: STS Model and Size: 1200x2400mm - 2.88m2
      Delivery Time: 2 - 4 days
      6mm STS Construction Board has numerous applications including over-boarding timber floors prior to tiling, as a cavity closure, eaves boards, under canopies, or as a ceiling board where fire rating is required. It is an A1 fire-resistant fibre-cement board which makes the structure safer in th..
      Brand: Wemico Model and Size: 2134
      Delivery Time: 1 - 2 days
      6mm Stainless Steel Base Track Clips for external wall thermal insulation board. Also available in aluminium and PVC. Only clips. 2.5m length ..
      Guide Price: £106.55
      £127.86 inc VAT
      Brand: Cellecta Model and Size: 75mm - 2.5m
      Delivery Time: 3 - 5 days
      75mm Cellecta Unicloser X Double Flange Cavity Closer made of  Hexatherm extruded polystyrene with two U-PVC damp proof course profiles. This cavity closer will eliminates cold bridging around window and door openings.CHARACTERISTICSHigh quality Hexatherm extruded polystyrene,2 R..
      75mm Cellecta Unicloser XPS Single Flange Cavity Closer - 2.5m length
      Guide Price
      Brand: Cellecta Model and Size: 75mm - 2.5m
      Delivery Time: 3 - 5 days
      75mm Cellecta Unicloser X Single Flange Cavity Closer made of  Hexatherm extruded polystyrene with one U-PVC damp proof course profiles. This cavity closer will eliminates cold bridging around window and door openings.CHARACTERISTICSHigh quality Hexatherm extruded polystyrene,Rigid U-PVC p..
      Brand: Wemico Model and Size: 3799
      Delivery Time: 1 - 2 days
      80x120mm PVC Corner profile with alkali resistant glass fibre mesh wings, which allows it to be cut to the required length and reduces waste. Can be folded to any angle. 2.5m length...
      Guide Price: £274.64
      £329.57 inc VAT
      Brand: Kingspan Model and Size: thermabate
      Delivery Time: 3 - 5 days
      85mm Thermabate Cavity Closer, an innovative solution designed to maintain continuous insulation around window and door openings. Crafted with a rigid thermoset urethane insulation core, this cavity closer box section ensures optimal thermal performance and condensation control. It adapts seamlessly..
      £207.30
      £248.76 inc VAT
      8X2 Galvanised Expanded Metal Lath Sheet - 685x2438mm
      Guide Price
      Brand: Teco Model and Size: 685x2438mm
      Delivery Time: 1 - 2 days
      8x2 Galvanised Expanded Metal Lath Sheet is mainly used for internal and external plaster when applied on suspended ceilings and walls. It is also suitable for encasing steel columns and beams, assisting in the protection from fire. Galvanised Steel EN 10346 DX51D Z275. Gauge: 0.4mm   ..
      Guide Price: £9.79
      £11.75 inc VAT
      Brand: Teco Model and Size: 700x2500mm
      Delivery Time: 1 - 2 days
      8x2 Stainless Sheet Expanded Metal Lath Sheet is mainly used for internal and external plaster when applied on suspended ceilings and walls. It is also suitable for encasing steel columns and beams, assisting in the protection from fire. In external applications and where there is regular exposure t..
      Guide Price: £57.77
      £69.32 inc VAT
      8mm RCM Cemboard - Cement Bonded Particle Board
      Guide Price
      Brand: RCM Model and Size: 2400x1200mm - 2.88m2
      Delivery Time: 1 - 2 days
      8mm RCM Cemboard is a medium density high performance cement bonded particle building board used primarily as an external sheathing or acoustic building board on both metal and timber frame structures. This rigid Cemboard offers great strength and stability with the workability of wood. RCM Cem..
      9mm Frameseal Bead with Protecting Lip and Mesh - length of 2.6m - article 37929 9mm Frameseal Bead with Protecting Lip and Mesh - length of 2.6m - article 37929
      Guide Price
      Brand: Wemico Model and Size: 37929 - 2.6m
      Delivery Time: 1 - 2 days
      9mm Frameseal Bead with Protecting Lip and Mesh length of 2.6m, article 37929 for plaster thickness 9mm. Made with Rigid PVC with soft PVC and glass fibre mesh...
      Brand: IPP Model and Size: 2400x1200mm - 2.88m2
      Delivery Time: 1 - 5 working days
      9mm Magply Render Carrier Board is a a high strength, breathable non-combustible board manufactured from MgSO4 and reinforcement meshes used for direct rendering, and has been tested with a variety of render systems by the British Board of Agrement.APPLICATIONExternal and internal direct render..
      Guide Price: £40.38
      £48.46 inc VAT
      Brand: STS Model and Size: 1200x800mm - 0.96m2
      Delivery Time: 2 - 4 days
      9mm STS Render Carrier Board is a heavy-duty, impact-resistant, dimensionally stable and weatherproof fibre cement construction board that provides a perfect surface to receive a thin coat render systems. Even though its recommend rendering as soon as conditions allow, the STS Render Carrier bo..
      Guide Price: £12.82
      £15.38 inc VAT
      Abrasive Tool (Grinder) for Polystyrene EWI Sheets Blue Dolphin - 270mm x 130mm
      Guide Price
      Brand: Blue Dolphin Model and Size: 270mm x 130mm
      Delivery Time: 1 - 2 days
      Abrasive Tool (Grinder) for Polystyrene EWI Sheets Blue Dolphin - 270mm x 130mm with an ergonomic plastic handle and removable steel piece. It is used for rasping and smoothing polystyrene boards used for insulating external walls. The abrasive surface shaves off the unwanted sections of the po..
      Guide Price: £20.25
      £24.30 inc VAT
      Brand: Wemico Model and Size: 91003
      Delivery Time: 2 - 3 working days
      Aluminium Bottom Section with Mesh Wing of the Render Only Compression Joint for thin coat render. Ideally suited to timber framed buildings. The aluminium base section is supplied pre-coated white, but can be powder coated to any colour if required. ..
      Guide Price: £191.70
      £230.04 inc VAT
      Brand: Wemico Model and Size: 9440
      Delivery Time: 1 - 2 days
      Aluminium Facade Corner Profile Without Covered Cutting Edges - Profile 9440 length of 3m. Corner profiles cover the cutting edges of the facade boards and form a clean, precise edge. Vertical corner profiles must be fastened at one fixed point at the top. If conditions require multiple fastening po..
      Brick Slips Britannia Range (pack of 30) Brick Slips Britannia Range (pack of 30)
      Guide Price
      Brand: Eurobrick Model and Size: Straight Brick Slips Britannia Range
      Delivery Time: 1 - 2 days
      Brick Slips Britannia range are slices of brick designed to replicate the look of masonry, typically fitted to a backing board or fixed with adhesives to a substrate. They are extruded from clay and wire cut into slimline profiles before being kiln-fired. They replicate the look of conventional bric..
      Guide Price: £22.42
      £26.90 inc VAT
      Brick Slips Classic Range (pack of 30) Brick Slips Classic Range (pack of 30)
      Guide Price
      Brand: Eurobrick Model and Size: Classic Range
      Delivery Time: 1 - 2 days
      Brick slips Classic range are slices of brick designed to replicate the look of masonry, typically fitted to a backing board or fixed with adhesives to a substrate. They are mostly cut from existing bricks. They replicate the look of conventional bricks, and can be supplied in a wide variety of..
      Guide Price: £41.25
      £49.50 inc VAT
      Brand: Cekol Model and Size: Cekol C-35 - 20kg
      Delivery Time: 1 - 2 days
      Cekol C35 Cement Based External Filler is a high quality material used for smoothing and improving of external walls of buildings. Cekol C-35 can also be used on internal walls, especially  in rooms exposed to high humidity such as bathrooms, kitchens. It is a dry mixture of high quality w..
      £26.24
      £31.49 inc VAT
      Ceresit CT 240 Winter - Additive for Wet Renders and Paints Drying Under Low Temperatures - 100ml
      sale!
      Brand: Ceresit Model and Size: CT240
      Delivery Time: 2 - 4 days
      Ceresit CT 240 Winter is a high quality accelerating additive for wet renders and paints drying under low temperatures in late autumn and early spring times, especially when the temperature fall below zero in the nights. This additive can be used for thin-coat acrylic renders - CT 60, CT 63, CT 64, ..
      £12.00 (£14.40 inc VAT)
      £11.40
      £13.68 inc VAT
      Brand: Ceresit Model and Size: CT280
      Delivery Time: 2 - 4 days
      Ceresit CT 280 Winter is a high quality accelerating additive for ETICS and wet renders drying under low temperatures in late autumn and early spring times, especially when the temperature fall below zero in the nights. This additive can be used for cement based mineral adhesive mortars - CT 83, CT ..
      Brand: Ceresit Model and Size: 1m x 25m - 25m2
      Delivery Time: 2 - 3 working days
      Ceresit CT 327 Glass-Fibre Mesh Roll is a reinforcing mesh for embedding into mortars for faades or pedestals exposed to higher stress or higher mechanical loads. It is a part of the Ceresit External Thermal Insulation Composite Systems (ETICS).CHARACTERISTICSAlkali-resistant, Slip proof, Tear proof..
      Ceresit CT 80 Universal Adhesive for Mineral Wool EWI Slabs, Polystyrene and Phenolic Boards
      Guide Price
      Brand: Ceresit Model and Size: CT80 - 25kg
      Delivery Time: 7 - 10 days
      Ceresit CT 80 is an adhesive mortar for fastening EWI mineral wool slabs, polystyrene and phenolic boards and also for making a thin layer of base coat render reinforced with fibreglass mesh on the insulation in Insulated Renders Systems. Ceresit CT 80 has very good adhesion to load-bearing, dense a..
      Guide Price: £15.20
      £18.24 inc VAT
      Brand: Ceresit Model and Size: CT100 - 25kg
      Delivery Time: 5 - 7 days
      Ceresit CT100 Impactum is a highly flexible dispersion reinforcing compound for making a reinforced layer with glass fibre mesh on expanded polystyrene boards. It is a part of Ceresit Ceretherm Impactum, external thermal insulation composite system for walls of buildings (ETICS). Ceresit CT100 can a..
      Guide Price: £61.75
      £74.10 inc VAT
      Ceresit CT17 Profi Deep-penetrating Primer - 5L
      sale!
      Brand: Ceresit Model and Size: CT17 - 5litres
      Delivery Time: 5 - 7 days
      Ceresit CT17 Profi is a deep penetrating primer for priming walls, floors, ceilings inside and outside buildings prior to fixing ceramic tiles, pouring floors, fixing floor lining, papering, puttying, painting, or fixing thermal insulation boards. It is highly recommended for aerated concrete, anhyd..
      £22.23 (£26.68 inc VAT)
      £21.12
      £25.34 inc VAT
      Ceresit CT177 Mosaic Render - 25kg
      Guide Price
      Brand: Ceresit Model and Size: CT177
      Delivery Time: 2 - 5 working days
      Ceresit CT 177 Mosaic Render is used for applying decorative colourful renders to traditional plasters, concrete substrates, gypsum substrates and chipboards, gypsum cardboards, etc. Transparent resins are the binder and coloured quartz gravels size of 1 - 1.6 mm are the fillers. This material is de..
      Brand: Ceresit Model and Size: 25kg
      Delivery Time: 5 - 7 days
      Ceresit CT29 Smooth Mineral exterior filler and skim coat is used for repairing traditional plasters and for making thin-layer rubs inside and outside buildings. It can be used both for filling deep cavities (e.g. furrows after installation works) and for smoothing plaster surfaces. Ceresit CT29 is ..
      £27.56
      £33.07 inc VAT
      Brand: Ceresit Model and Size: CT42
      Delivery Time: 2 - 3 working days
      Ceresit CT42 Acrylic Paint is used for protecting facades, concrete constructions and interiors. It can be applied on concrete, cement plasters, lime-cement plasters and lime plasters. This paint can be used for painting Ceresit CT 35, CT 36 and CT 137 mineral plasters, Ceresit CT 60, CT 63, CT 64 a..
      Guide Price: £65.34
      £78.41 inc VAT
      Ceresit CT48 Silicone Paint (3.5 litres)
      Guide Price
      Brand: Ceresit Model and Size: CT48 - 3.5l
      Delivery Time: 2 - 3 working days
      Ceresit CT 48 Silicone Paint is used for protecting facades, concrete constructions, interiors. It can be applied on the mineral substrates such as concrete, cement plasters, lime-cement plasters and lime plasters that have never been painted before. This paint can be used for painting mineral plast..
      Guide Price: £38.00
      £45.60 inc VAT
      Brand: Ceresit Model and Size: CT49
      Delivery Time: 2 - 3 working days
      Ceresit CT 49 Silix XD nano-silicone paint had been created from a formula of selected and modified silicone resins, polysiloxane resins, special fillers and pigments. The addition of the Polytetrafloroethylene (PTFE) additives to the recipe gives an extremely high degree of hydrophobia to the surfa..
      Guide Price: £120.00
      £144.00 inc VAT
      Ceresit CT60 Acrylic Render 0.5 mm grain
      Guide Price
      Brand: Ceresit Model and Size: 25kg - 0.5 mm grain
      Delivery Time: 1-3 working days
      Ceresit CT60 is used for making thin-layer renders in External Wall Insulation Systems, on concrete substrates, on traditional renders, gypsum substrates and chipboards, gypsum cardboards, etc. It is recommended use CT 60 as facade render within Ceresit ETICS (External Thermal Insulation Composite S..
      Showing 121 to 150 of 213 (8 Pages)