40mm Unilin XtroLiner XO/PR Pitched Roof PIR Insulation Board - 1200mm x 2400mm - Pack of 7
40mm Unilin XtroLiner XO/PR Pitched Roof PIR Insulation Board - 1200mm x 2400mm - Pack of 7
- Product Code: A1-5013
- Delivery Time: 1-3 working days
- Brand: Unilin (prev. Xtratherm)
- Model and Size: 1200x2400mm - 20.16m2
Our ratings on 01-08-2025:
4.8 out of 5
40mm Unilin XtroLiner XO/PR Pitched Roof PIR Insulation Board - 1200mm x 2400mm - Pack of 7
Length: 2400mm
Width: 1200mm
Thickness: 40mm
Pack Quantity: 7
Board Coverage: 2.88m2
Pack coverage: 20.16m2
Thermal Conductivity: 0.021W/mK
R-Value: 1.9m2K/W
Compressive Strength: 150kPa
40mm Unilin XtroLiner XO/PR board has a core of modified polyisocyanurate (PIR) bonded to low emissivity textured aluminium foil facings. Unilin XtroLiner XO/PR board offers excellent insulation performance with excellent thermal conductivity. Unilin XtroLiner XO/PR is CFC & HCFC free and is manufactured under the highest standards of ISO 9001 and 14001 Quality and Environmental Management Systems.
Note: This product was formerly known as 40mm Xtratherm XtroLiner XO/PR Pitched Roof PIR Insulation Board
CHARACTERISTICS
- High Thermal Performance Rigid Insulation,
- Easy to Install,
- Non-deleterious material,
- Suitable for new build and refurbishment,
- Manufactured with zero ODP blowing agent,
- Reduces Thermal Bridging,
- Reaction to fire: Euroclass C s2 d0,
- Closed cell structure – moisture resistant
APPLICATION
- Pitched roof
- Ventilated roof
- Warm roof
- Above and between rafters
- Under rafters, above ceilings
INSTALLATION
Ventilated Roofs
- Allow for ventilation gaps normally 50mm. (May be reduced depending on breather membrane certification).
- Cut XtroLiner boards to fit tightly between rafters flush with rafter bottom. An additional 2nd layer should be added to the underside of the rafter.
- Run second layer transverse to the first.
- Temporarily fix with nails.
- Provide vapour control layer (Aluminium tape joints).
- Finish with 12.5mm plasterboard fixed with drylining screws. Screw fix every 150mm, 12mm from edge of boards.
- All board edges should be supported.
Warm roofs
- Ensure cavity wall insulation has continued to roof height to engage with roof insulation.
- Fix a timber stop rail to end of rafter at eaves.
- Lay Unilin XtrolinerXO/PR insulation stagger jointed over rafters ensuring joints are supported by rafters.
- Ensure boards are tightly butted fill any gaps with expanding foam. A vapour permeable underlay should be fitted; refer to manufacturers Agrèment certification.
- Providing an unvented void under the membrane can improve the thermal performance.
- Fix counter batten with approved fixings.
- Ventilation may have to be provided subject to certification.
- A second layer of insulation may be added between the rafters.
- Provide a vapour control layer to the underside of the construction.
- Current Building Regulations/Standards should be considered with regard to the requirements for and/or provision of fire stops.
CERTIFICATION
Unilin_XO_PR_Datasheet.pdf
Brand: Unilin (prev. Xtratherm)
Model and Size: 1200x2400mm - 11.52m2
Delivery Time: 1-3 working days
75mm Unilin Thin-R Hyfloor XT/HYF is a high performance floor Insulation board with superior thickness to performance ratio allowing the lower targets required under the new Building Regulations to be achieved with minimum thicknesses. Unilin Thin-R Hyfloor XT/HYF is a high performance foil faced Po..
Brand: Unilin (prev. Xtratherm)
Model and Size: 1200x2400mm - 14.40m2
Delivery Time: 1-3 working days
60mm Unilin XtroLiner XtroDeck XO/XD board has a core of modified polyisocyanurate (PIR) bonded to low emissivity embossed aluminium foil facings. Unilin XtroLiner XtroDeck XO/XD board offers excellent insulation performance with excellent thermal conductivity.Unilin XtroLiner XtroDeck XO/XD bo..
Guide Price
Brand: Unilin (prev. Xtratherm)
Model and Size: 1200mm x 1200mm - 4.32m2
Delivery Time: 3 - 5 days
140mm Unilin FR-BGM is a a BBA certified high performance PIR insulation board that is faced with a fleece finished bitumen/glass facers and is suitable for use below partially bonded bitumen based built up roofing systems. Unilin FR-BGM is suitable to apply torch on felt directly on the insulation...
Guide Price: £133.30
£159.96 inc VAT
Guide Price
Brand: Unilin (prev. Xtratherm)
Model and Size: 2400mm x 1200mm - 2.88m2
Delivery Time: 1-3 working days
50mm Unilin Thin-r XT/PR-UF has a core of polyisocyanurate (PIR) bonded to low emissivity textured aluminium foil facings. Unilin XT/PR-UF board offers excellent insulation performance with excellent thermal conductivity. Unilin XT/PR-UF is CFC & HCFC free and is manufactured under the high..
Guide Price: £22.40
£26.88 inc VAT
Brand: Unilin (prev. Xtratherm)
Model and Size: 1200mm x 450mm - 1.62m2
Delivery Time: 2 - 4 days
140mm Unilin Thin-R Plus XT/CF is a superior performance, enhanced polyisocyanurate (PIR) insulation, specifically engineered for full-fill thermal insulation in new external masonry cavity walls. This advanced insulation board is designed to meet and exceed the stringent thermal requirements of Bri..
Guide Price
Brand: Unilin (prev. Xtratherm)
Model and Size: 1200mm x 1200mm - 25.92m2
Delivery Time: 3 - 5 days
25mm Unilin FR/MG is a high performance PIR core with mineral coated glass facers suitable for use below single ply waterproofing systems and partially bonded built-up felt. It is compatible with adhesively bonded single ply roofing membranes laid on mechanically fixed ..
Guide Price: £219.09
£262.91 inc VAT