Plastestrip Galvanised Steel C-Channel - ST/CH/30/210 - 3m length
Plastestrip Galvanised Steel C-Channel - ST/CH/30/210 - 3m length
- Product Code: A1-6802
- Delivery Time: 7 - 10 days
- Brand: Plastestrip (Tech. support: 0172674771)
- Model: ST/CH/30/210 - 3m length
Our ratings on 13-04-2026:
4.8 out of 5
Plastestrip Galvanised Steel C-Channel - ST/CH/30/210 - 3m length
Length: 3000mm
Width: 210mm
Height: 30mm
Thickness: 2mm
Fire Rating (Reaction to Fire): A1(Non-combustible)
Plastestrip Galvanised Steel C-Channel - ST/CH/30/210 is a robust, open-faced profile designed to provide a flat, recessed mounting track for the brackets. These horizontal support profiles act as a structural "bridge" between building studs. By installing these horizontally across the face of the studs, you create a continuous mounting surface. This allows the FastFrame or ThermaFrame "helping hand" brackets to be positioned exactly where the facade design requires them, rather than being restricted to the fixed centres of the building's internal frame. The Galvanised Steel C-Channel is a universal component used across both the FastFrame and ThermaFrame systems.
CHARACTERISTICS
- Manufactured from S275 structural-grade galvanised steel.
- A wider 210mm channel designed to accommodate double or XL brackets, which are used to take the heavier "dead loads" at fixed points in the system.
- Allows the "helping hand" brackets to be positioned exactly where the facade design requires them.
- A universal component used across both the FastFrame and ThermaFrame systems.
FastFrame-Typical-details.pdf
Brand: Plastestrip
Model: AL/TP25
Delivery Time: 7 - 10 days
PlastiClad Aluminium Vertical Joint AL/TP25 is a high-performance H-profile trim specifically designed for lapped weatherboard cladding systems. It provides a structured, weathertight, and aesthetically pleasing solution for joining two runs of weatherboard planks end-to-end on a continuous flat wal..
Brand: Plastestrip
Model: PL-PTS-WASH-1.6
Delivery Time: 7 - 10 days
1.6mm Plasticlad Stainless Steel Spacer Washer is a premium component designed for use with PTS fixings in rainscreen cladding systems. These washers are specifically designed to create a defined gap between the cladding panel and the supporting subframe (whether timber or metal).CHARACTERISTICSManu..
Brand: Plastestrip
Model: 555-020-856
Delivery Time: 7 - 10 days
Undercut Anchor for 5.5mm Embedment is a specialised mechanical fixing designed for the high-end "secret fix" installation of thin cladding panels, typically High-Pressure Laminate (HPL), ceramic, or natural stone. The undercut anchor relies on a precise "undercut" geometry drilled into the rear of ..
Brand: Plastestrip
Model: AL/ST60
Delivery Time: 7 - 10 days
PlastiClad Aluminium Starter Trim AL/ST60 is the foundational component of any weatherboard installation. It is the very first profile to be installed, ensuring that the first course of cladding planks is set at the correct angle and height. It is fixed horizontally at the lowest point of the i..
Brand: Plastestrip
Model: FF FIX/BRD/80
Delivery Time: 7 - 10 days
80mm Plastestrip FastFrame Aluminium Double Helping Hand Bracket - FF FIX/BRD/80is the primary load-bearing component within the Plastestrip sub-frame system. While the single bracket is typically used for intermediate wind-load support, the double bracket is engineered to act as the Fixed Point, ca..
Brand: Plastestrip
Model: 864134
Delivery Time: 1-3 working days
32mm Plastestrip Colour Coated Annular Ring Shank Nails for fixing panels to timber. A4 stainless steel (316 grade). Can be powder coated to any colour. ..