External Wall Insulation Systems

  • Polystyrene Insulation - EPS, XPS, Grey
  • Phenolic Insulation
  • Glass wool, Rock wool Insulation
  • Polyisocyanurate (PIR) Insulation
  • EWI Accessories

Heat moves from warmer to colder areas. Therefore, on cold days, heat from inside a building seeks to get outside. And on warmer days, the heat from outside the building seeks to get inside. Insulating the external walls would slow the movement of heat out through the walls thereby dramatically reducing heating demand. 

Most buildings in UK are constructed with solid walls. They dont have cavities that can be filled or injected with insulation. These solid external walls need to be insulated by adding a layer of insulation to either to the interior face or to the exterior face of the wall. The best method is to insulate the walls on its exterior face. The savings on your heating bills will be bigger, and those savings would have a great impact on your budget.

In a typical building, around 40% of the energy used to heat or cool a room is wasted due to poorly insulated external walls. Correctly chosen external wall insulation (EWI) systems dramatically cut energy loss by wrapping the building in a thermally resistant envelope and also provide lasting protection for the entire structure of the building. The external wall insulation system involves an entire set of different products and accessories, so it is important to make sure that you get all quality products you need from one place. Here at Insulation Shop we provide just that  a complete set of high quality insulation products and all necessary accessories for insulating your exterior walls. The best possible building performance can only be realised if walls are externally insulated.

Benefits of EWI Systems
  • External wall is warm and dry, increasing thermal performance and reducing building maintenance,
  • The heat retention capability of the existing wall is fully utilised,
  • Removes of cold bridges reducing the risk of condensation, damp and mould,
  • Eliminates cracking caused by thermal expansion and contraction,
  • Lightweight construction methods can be used, allowing for fast installation,
  • Reduces heating costs by up to 40%,
  • Reduces maintenance costs,
  • Improves the living environment: - Warmer in Winter - Cool in Summer
  • Protects the building fabric and enhances the aesthetics,
  • Does not encroach on living space,
  • May increase the value of your property

External Wall Insulation (EWI) is a system, which not only insulates, but also protects the exterior of your home. External wall insulation involves fixing a layer of insulation material to the wall, then covering it with a special type of render or cladding. This finish can be smooth, textured, painted, tiled, brick slipped, dry-dashed or panelled.

The usual EWI system consists of insulation, adhesive render or base coat, insulation fixings, polypropylene or glass fibre mesh, primers, decorative surface finishes and also beads, trims and flashings.

  • The insulation is the main thermal layer, and also the background for applying the adhesive render, basecoat and finishes to. Various types of insulation are available The choice of the insulation is dependant on the required thermal performance, zoning, location and cost. The rigid or semi rigid insulation boards are fixed either directly with adhesive, with insulation fixings, or a combination of both.
  • Adhesive renders are applied to the rear of the board in either a dot and dab method, with the perimeter of the board being coated and two slobs in the middle, or with a serrated edge trowel to the entire rear of the insulation board.
  • Insulation fixings used in most EWI systems. These are specified to suit the existing substrate, the height and shape of the building, its location and elevation, and proximity to other buildings. Most times, a combination of adhesive render and insulation fixings are used. 
  • Most basecoats used are polymer modified cement based renders, which are weatherproof and can accommodate varying degrees of thermal movement. Basecoats are reinforced with a mesh over the top of the insulation layer. The reinforcement layer would spread stresses across the facade surface into the insulation below, provide impact resistance to the system and enhance weatherproofing.
  • The final decorative surface finish would provide added weather proofing properties to the building envelope. This finish can be smooth, textured, painted, tiled, brick slipped, dry-dashed, wet-dashed or panelled. It cold be acrylic textures, silicone textures, mosaic textures, mineral renders and brick effect renders.
  • All EWI systems require the use of beads, trims and flashings. They are used as starters, junctions and closers.
Types of Insulation for EWI systems

  • Expanded polystyrene (EPS) White & Grey,
  • Extruded polystyrene (XPS),
  • Phenolic, 
  • Glass wool and Mineral (Stone) wool, 
  • Polyisocyanurate (PIR)

Expanded Polystyrene (EPS) White & Grey Installation

Expanded Polystyrene (EPS) is a lightweight, rigid, plastic foam insulation material, which a cost effective, easy-to-use product for EWI applications. The structure of EPS consists of 98% air. Its initial thermal properties are maintained throughout its working life. It is non-toxic, moisture resistant and rot proof.

Grey Polystyrene (Graphite) is a high quality expanded polystyrene (EPS) board enhanced with integrated graphite within its bead structure. The high-purity graphite particles integrated within the insulation beads reflects radiant heat and significantly improves insulation capability, providing up to 20% greater r-value than traditional white EPS of the same thickness. Warm air always moves towards cold air, In Grey Polystyrene (Graphite) the path taken by warm air moving towards the cold air takes many twists and turns along the way, slowing down the heat transfer, keeping the premises warmer.

Benefits
  • Cost effective - cheapest insulation material in the market. 
  • Easy to cut using a fine tooth saw or hot wire cutter,
  • The surface can be rasped on site to remove level differences,
  • Durable, not affected by short exposure to UV or rain.
  • Long term exposure can cause slight discolouration, but does not affect the thermal performance,
  • Has a high K-value when compared with other insulations,
  • Can be used in low rise and high Rise applications and in coastal locations,
  • Does not absorb moisture and its thermal and mechanical properties are unaffected by damp, humidity or moisture,
  • 100% recyclable.
Precautions
  • Should be kept away from solvents, 
  • Should not be exposed to naked flame,
  • Classified as combustible (combustibility is limited due to retardants present),
  • Should be stored in protected packaging and away from direct sunlight.

Extruded Polystyrene (XPS) Installation

XPS is a closed cell extruded polystyrene insulation with good thermal and water resisting properties having a high compressive strength. A wide range of thicknesses are available to achieve the thermal values required. Extruded polystyrene can withstand extreme loads. Used mainly below ground applications.

Benefits
  • Able to withstand extreme loads, 
  • Below ground applications,
  • Easy to cut using a fine tooth saw or hot wire cutter,
  • Highly water resistant,
  • Can be stored and installed in severe wet weather conditions with no deterioration during its life,
  • Durable, not affected by short exposure to UV or rain.
  • Has a high K-value when compared with other insulations,
  • Can be used in low rise and high Rise applications and in coastal locations,
  • Does not absorb moisture and its thermal and mechanical properties are unaffected by damp, humidity or moisture,
  • 100% recyclable.
Precautions
  • Should be kept away from solvents, 
  • Should not be exposed to naked flame,
  • Classified as combustible (combustibility is limited due to retardants present),
  • Can react to PVC cables and cause cables to become brittle, therefore a conduit should  be used.

Phenolic Insulation

Rigid phenolic insulation is produced by mixing high solids and phenolic resin with a surface acting agent. The heat created by the reaction evaporates a volatile liquid blowing agent in the mixture which produces a network of small bubbles in the material. This insulating core is bonded to two flexible tissue faced layers. The rigid phenolic insulation offer very good thermal insulating properties due to the very low thermal conductivity of phenolic foam. It can actually be 50% more effective than other common insulation materials. Its low thermal conductivity allows specified thermal performance targets to be achieved with minimal thickness of insulation, and saves space.

Kingspan Kooltherm K5 External Wall Board is a one of the top selling phenolic core external wall insulation boards, applicable to both solid and cavity brick and block walls.Kingspan Kooltherm K15 Rainscreen Board is specially created board to be used as a rainscreen in most frame buildings. Xtratherm Safe-R is another phenolic rigid EWI board available at the Insulation Shop.

Benefits
  • Offers the best K-value of all the available insulation - thinner boards required,
  • Easy to cut using a fine tooth saw,
  • High closed cell content and fine cell structure,
  • Lightweight, easy to transport , handle and install,
  • Resistant to fungus and mould growth and will not sustain vermin,
  • Highly resistant to moisture penetration,
  • Dimensionally stable and can be cut accurately to achieve a snug fit,
  • Self extinguishing, low smoke emission, 
  • Can be used in low rise and high Rise applications and in coastal locations.
Precautions
  • Should be kept dry, 
  • Should not be used if effected by rain until it has been dried out,
  • Should not be exposed to naked flame,
  • Should not be left exposed for long periods of time to direct sunlight and rain, 
  • Classified as combustible (combustibility is limited due to retardants present),

Mineral Fibre - Glass wool, Rock wool Insulation

Glass mineral wool is made from sand and recycled glass, limestone and soda ash. The glass is spun to form millions of fine fibres. A resin is used to bind the long fibres together to form a mat of material giving good tear strength. The density of the product determines whether the insulation is a lightweight quilt supplied in rolls, a flexible slab or a rigid slab, and its thermal insulation value.

Rock wool (also known as mineral wool or stone wool) is manufactured from molten rock in a furnace through which a stream of air or steam is blown at temperature of about 1600 C. The final product creates a mass of fine, intertwined fibres which may contain binder (often food grade starch) and an oil to reduce dusting. When pressed into rolls and sheets their ability to partition air makes them excellent heat insulators and sound absorbers. The insulation is produced in a variety of densities according to format and function. High quality Rockwool Fasrock-LL External Wall Insulation Slab and Rockwool Frontrock MAX E Dual Density External Wall Insulation Slab are available at Insulation Shop.

Benefits
  • The only insulation to be classed as non-combustible,
  • Offers good K-values,
  • Production emissions within UK legal defined limits,
  • Reduces overall environmental impact and formaldehyde-free,
  • Non skin irritant,
  • Easy to handle and work,
  • Resistant to rot,
  • Excellent acoustic and thermal properties,
  • Recyclable, 
  • Can be used in low rise and high Rise applications and in coastal locations.

Precautions
  • Should be stored on a flat, covered, protected surface, 
  • Should be kept dry, 
  • Should not be left exposed for long periods of time to rain,
  • Should not be used if effected by rain until it has been dried out,
  • Should limit the area of application of the boards and to basecoat at the earliest chance to avoid the boards becoming wet.

Polyisocyanurate (PIR) Insulation

Polyisocyanurate (PIR) insulation is a closed-cell rigid foam board manufactured with isocyanate and polyether mixed together in the presence of a catalyst that allows the molecules to rearrange, forming closed cells. It has a wider operating temperature range that surpasses standard polystyrene and is fire and smoke resistant. PIR insulation is available as a sprayed foam and as a rigid foam board. PIR does not require a thermal moisture barrier prior to installation. Celotex SW3000 is a PIR EWI board available at Insulation Shop, but would be sold at minimum run of 600m2.

Benefits
  • Offers the best K-value of all the available insulation - thinner boards required,
  • Easy to cut using a fine tooth saw,
  • High closed cell content and fine cell structure,
  • Lightweight, easy to transport , handle and install,
  • Resistant to fungus and mould growth and will not sustain vermin,
  • Highly resistant to moisture penetration,
  • Dimensionally stable and can be cut accurately to achieve a snug fit,
  • Can be used in low rise and high Rise applications and in coastal locations.
Precautions
  • Should not be exposed to naked flame.
  • Should be kept dry, 
  • Should not be used if effected by rain until it has been dried out,
  • Should not be left exposed for long periods of time to direct sunlight and rain, 
  • Classified as combustible (combustibility is limited due to retardants present),
Types of Render

  • Acrylic renders
  • Mineral renders
  • Mosaic renders
  • Silicone renders

Acrylic render

Acrylic render is a finishing coat for render, containing acrylic aggregates to display an attractive finish. It is much more resistant to cracking than other types of render. Acrylic render is available in a wide range of colours and textures ranging from 1mm to 3mm aggregate size.Acrylic render is also fast drying, taking only two days to cure and dry while traditional renders can take up to 28 days. Acrylic render can be used to cover up small hairline cracks in masonry surfaces. The minute reinforcing fibres in Acrylic renders produce an incredibly tough and durable finish. It is permeable to water vapours and allows the substrates (brick etc) to breathe. It is also resistant to efflorescence (the white salts that sometimes leak from brickwork). Acrylic render can be trowelled on or rolled or even sprayed onto a surface. Two coats are generally applied.

Benefits
  • Easy to apply,
  • Easy to clean,
  • Lasts longer - about 8 years,
  • Covers hairline cracks,
  • Water vapour permeable,
  • Allows substrates to breathe,
  • Resistant to efflorescence,
  • Resisting driving rain,
  • Resists UV,
  • Can be trowelled on or rolled or even sprayed,
  • Available in a wide range of colours and textures.
Precautions
  • Should be cleaned of fallen leaves  - might grow algae

Mineral render

Mineral Render is eco-friendly, manufactured from natural materials such as mineral aggregates, and white marble grain. It is available with a rolled texture in 2, 3 and 4mm grain sizes. Mineral Render is highly damage resistant and also is Class 0 surface spread of flame. Mineral render contains cement contact allowing the product to set quicker, so it can be easily used during lower temperature periods. 

Benefits
  • Easy to apply,
  • Easy to clean,
  • Highly damage resistant,
  • Covers hairline cracks,
  • Sets quickly - contains cement,
  • Can be used during lower temperature periods,
  • Fire resistant,
  • Allows substrates to breathe,
  • Resisting driving rain,
  • Resists UV,
  • Available in a wide range of colours and textures,
  • Made entirely from natural materials.

Mosaic render

Flexible and easy to clean render with increased scratch resistance and covering ability. Suitable for indoor and outdoor use on walls exposed to high wear: at plinths, entrances, hallways, window and door reveals. Sealing component: transparent resins. Filler: coloured quartz stone. Can be applied and smoothed with stainless steel trowels. Produces a glassy, colourful coat upon setting. Mosaic render can be used on concrete substrates and traditional plasters etc. 

Benefits
  • Easy to apply and clean,
  • Can be applied and smoothed with stainless steel trowels,
  • Increased scratch resistance, 
  • Covers hairline cracks,
  • Sets quickly - contains cement,
  • Can be used during lower temperature periods,
  • Fire resistant,
  • Allows substrates to breathe,
  • Resisting driving rain,
  • Resists UV,
  • Available in a wide range of colours and textures.

    Precautions
    • Might collect dirt

    Silicone render (Polymer render)

    Polymer render is a cement based system with specially selected polymers added to the mix. These polymers make the finished coat strong yet flexible, allowing them to be used on any substrate. Polymer renders incorporate silicone water repellents as an integral part of the cement based render system. This silicone technology allow water vapour to pass through the render, letting the substrate breathe. The use of nylon reinforced base coats provides a high strength base for the finish coat. Polymer render is available as one coat render, eliminating the need for a base coat. Polymer renders come in a wide range of colours and can be finished in different textures, from a flat sponged float finish or a rougher scraped finish as well as Pebble Dash. They are usually premixed and only require the addition of clean water to produce the final product. This ensures the quality of the render remains consistent and ensures a superior finish.

    Benefits
    • Tough cement based render,
    • Can be applied on a range of substrates,
    • Increased scratch resistance, 
    • Covers hairline cracks,
    • Allows substrates to breathe,
    • Textures could be smooth or dry or wet dashed,
    • Fire resistant,
    • Available premixed,,
    • Resisting driving rain,
    • Resists UV.

      Precautions
      • Might collect dirt

      Installation of EWI Systems

      To correctly specify which insulation system to use, the existing wall envelope should be examined.

      • Check the walls for any visual defects,
      • Check for rising damp and its causes,
      • Check for existing movement joints,
      • Carry out a line and level survey to determine if a levelling coat is required,
      • Check for efflorescence (the white salts that sometimes leak from brickwork),
      • Check the need for repositioning of,  temporary removal or extension of services such as electricity, gas, telephone, TV or internet.
      • Also, check if building permission is required.

      The drawings and specification would include,

      Installation

      • The wall should be cleaned from dirt, grime, algae etc, and be allowed to fully dry out, 
      • If a building has an existing rendered finish, and If the render is in a poor condition--by trapping water, transmitting damp, and not allowing the existing building to breathe, then it is better to remove the render,
      • Check the line and level of any existing building, and the uneven surface of the wall should be corrected,
      • Carry out a pull-out test for adhesives and insulation fixings,  
      • EWI boards should be protected from adverse weather, direct sunlight and possible impact damage,
      • Insulation work should only done in dry conditions, 
      • Boards should be laid in a staggered pattern,
      • They should be staggered at the edges of buildings so that they form a toothed finish,  
      • The boards should be cut in an L shape around the corners of openings,
      • No small cuts of boards are allowed be used, 
      • Gaps between boards should be limited, and if that happens the gaps should be filled tight fit with the same type of insulation,
      • Boards should be level so that the basecoat and decorative finish are installed on a flat surface,
      • Beads and trims to be fixed at given locations, starter tracks at the beginning, beads and trims as the work progresses,
      • Adhesive renders should be applied to the rear of the board, and should follow either a dot and dab method to the board edges, or a fully applied adhesive using a serrated trowel,
      • Mechanical anchors, insulation fixings should be used as per specification,
      • Insulation fixings should be installed at 90 degrees from the wall face, and the washer head sitting flush with the insulation board face,
      • Application of basecoat should only be carried out when the weather is fine and free from rain,
      • In a thin basecoat system, the application of any mesh should occur at the first basecoat stage,
      • Meshes for the thick basecoat system are generally metal laths types and are fixed to the insulation prior to first base coat,
      • Meshes should be installed into the wet basecoat, using the back of a steel trowel and pushed in, so that they sit in the top third,
      • Meshes should be continuous, and should have a minimum 100mm lap with the adjacent mesh to ensure strength and continuity of the basecoat,
      • Once the basecoat has been applied, it should be left to cure to receive the final finish,
      • Finishes should only be applied in good weather and within ambient temperatures (5-30 C), 
      • Finishes should be stored in areas that can achieve a constant temperature, and should not drop below 5C,
      • Textured finishes should be applied with a steel trowel and rubbed with a plastic or nylon trowel to reveal the aggregate,
      • Junctions are finished with a mastic sealant, however its use should be kept to a minimum as they have a short life cycle and will need to be maintained at regular intervals,
      • General good practice would be to fill the gap with the silicone sealant and the final finish taken over the top.

      Typical installation examples

      EWI Cladding systems

      • The actual method of installation will depend on the chosen cladding system.
      • External expanded polystyrene should be cut to ensure a tight fit between the battens and should be wedged into position.
      • If there is an an air gap between the insulation and the cladding, the EPS external boards should be pinned in place using corrosion-free fixings. 
      • A breathable sarking felt should be placed over the insulation, and the edges and joints sealed.
      • As the use of a single layer of EPS external insulation fitted between standard 38-50mm battens will not provide a U-value which satisfies the Building Regulations, a second layer of EPS external board should be fixed over the battens.
      • The cladding system should be efficiently fixed back to the main wall to prevent vertical downward drag of cladding in accordance with the cladding manufacturers instructions.

      Cladding is a non-load bearing skin attached to the outside of a home to shed water and protect the building from the effects of weather and also the key element in the aesthetic appeal of the building. It also directly influences both building cost and property value. The embodied energy, resource depletion and recyclability of the cladding must be balanced against maintenance and durability appropriate to life span. The roles of cladding include sound and thermal insulation, fire resistance and easy cleaning.

      Cladding is typically made from wood, metal, vinyl, masonry and a range of composite materials. Cladding systems include horizontal or vertical boards, overlapping panels or smaller panels such as shingles and tiles. It can be attached directly to the frame or to an intermediate layer of spacers. Cladding is generally considered as non-load bearing, however, some sheet cladding systems can have a structural role when fixed to the frame such as fibre reinforced cement sheeting, reconstituted composite timber, structural plywood. 

      R-value Comparison Chart for External Wall Insulation available at Insulation Shop

      Legend 

      1* Rockwool Frontrock Max-E External Wall Insulation Slab

      2* Rockwool Fasrock-LL External Wall Insulation Slab

      3* Kingspan Kooltherm K15 Rainscreen Board

      4* Xtratherm Safe-R Insulation Board

      5* Kingspan Kooltherm K5 External Board

      6* Grey Polystyrene (Graphite) EPS Board

      7* Cellecta Hexatherm XPeri Perimeter Wall Insulation Board, Sundolitt XPS300 Extruded Polystyrene Board

      8* Cellecta Hexatherm XPeri Perimeter wall Insulation Board

      9* Jablite EPS100 Polystyrene Insulation Board

      10* Kay-Metzeller EPS70 Polystyrene Insulation Board

      11* Jablite EPS70 Polystyrene Insulation Board, Jablite External Wall Polystyrene Insulation Board

      12* White Polystyrene Boad EPS


           




      Get a quote for EWI System

      Choose subcategory or scroll down to see products

      Filter by MANUFACTURER  

      Show:
      Sort By: Limit:

      30mm Sundolitt XPS300 Extruded Polystyrene Board (pack of 14)

      30mm Sundolitt XPS300 Extruded Polystyrene Board (pack of 14)

      1200x600mm - 10.08m2  show quantity discountsDelivery Time: 2 - 3 days

      Guide Price: £58.12 (£69.74 inc VAT)

      £5.77/m2 (£6.92/m2 inc VAT)

      show quantity discounts

      30mm Sundolitt XPS300 is an extremely durable thermal insulation board made of extruded polystyrene offering exceptional thermal performance and versatility. It is a lightweight board that is able to withstand extreme loads. Sundolitt XPS300 is highly water resistance, so can be stored and installed..

      Guide Price: £58.12 (£69.74 inc VAT)

      £5.77/m2 (£6.92/m2 inc VAT)

      show quantity discounts
      = m2
      other thicknesses
      40mm Jablite External Wall Polystyrene Insulation Board EPS - pack of 15

      40mm Jablite External Wall Polystyrene Insulation Board EPS - pack of 15

      Jablite 40mm - 10.80m2  Delivery Time: 3 - 4 days

      40mm Jablite External Wall Insulation Board is a very lightweight and easy to handle and install EPS 70wall board containing a flame-retardant additive, designed to be used as a part of various external wall insulation systems. It can be bonded or mechanically fixed to the wall. Installing insulatio..

      = m2
      other thicknesses
      50mm EPS100 Polystyrene Insulation Board Jablite (pack of 12)

      50mm EPS100 Polystyrene Insulation Board Jablite (pack of 12)

      2400x1200 - 34.56m2  Delivery Time: 3 - 7 days

      Guide Price: £177.20 (£212.64 inc VAT)

      £5.13/m2 (£6.16/m2 inc VAT)

      50mm Jablite EPS 100 board is a lightweight and cost efficient product which can be used for insulation of different constructions, including roofs, floors and walls, since it provides constant and stable thermal performance under different temperature conditions. It is made from expanded polystyren..

      Guide Price: £177.20 (£212.64 inc VAT)

      £5.13/m2 (£6.16/m2 inc VAT)

      = m2
      other thicknesses
      50mm FPR Insulation Panel Fixings (pack of 500)

      50mm FPR Insulation Panel Fixings (pack of 500)

      50x8 FPR - Free Delivery  show quantity discountsDelivery Time: 1 - 2 days

      £34.84 (£41.81 inc VAT)

      show quantity discounts

      50mm Polypropylene Insulation fixings for rigid and semi-rigid insulating boards and panels.APPLICATIONConcreteSolid stoneSolid brick..

      £34.84 (£41.81 inc VAT)

      show quantity discounts
      other lengths
      60mm Rockwool Frontrock  MAX E  Dual Density External Wall Insulation Slab 1000x600mm (pack of 4)

      60mm Rockwool Frontrock MAX E Dual Density External Wall Insulation Slab 1000x600mm (pack of 4)

      1000x600mm - 2.40m2  Delivery Time: 3 - 7 days

      Due to nationwide shortage the lead time may be longer for this product.

      60mm Rockwool Frontrock MAX E is a rigid dual density thermal and acoustic insulation slab made from volcanic rock, thus extremely durable, fire resistant and specifically created for external wall applications to go directly under render. The higher density surface of the slab is to take the r..

      = m2
      other thicknesses
      Ceresit CT190 Adhesive and Reinforcing Mortar for Mineral Wool External Wall Insulation Slabs

      Ceresit CT190 Adhesive and Reinforcing Mortar for Mineral Wool External Wall Insulation Slabs

      CT190  Delivery Time: 2 - 3 days

      Ceresit CT 190 mortar is designed to warm up external walls of the buildings by application of external thermal insulation composite system using mineral wool faade boards. It is an element within Ceresit Wool Classic insulation system. Ceresit CT 190 mortar is used for fixing of mineral wool faade ..

      = m2
      50mm Soffit Flashing and Window Sill Extensions (with full end caps-pair) - 2.5m Length.

      50mm Soffit Flashing and Window Sill Extensions (with full end caps-pair) - 2.5m Length.

      WEC741/50- Free Delivery  show quantity discountsDelivery Time: 1 - 2 days

      £45.97 (£55.16 inc VAT)

      show quantity discounts

      50mm Aluminium Soffit Flashing and Window Sill Extensions suitable for most conditions requiring the weathering of External Wall Insulation Systems and Rendering. Aluminium White Coated with peel-off low tack film to protect the section during transportation and fixing on-site. J..

      £45.97 (£55.16 inc VAT)

      show quantity discounts
      other widths
      10mm PVC Drip Bead (pack of 25).

      10mm PVC Drip Bead (pack of 25).

      D10 - Free Delivery  show quantity discountsDelivery Time: 1 - 2 days

      £64.58 (£77.50 inc VAT)

      show quantity discounts

      10mm PVC Drip Beads are designed for various rendering applications and external wall insulation providing impact and rainwater protection, installed above the damp proof courses or window and door reveals. Their main function is to provide a drip for rainwater and prevent return of the water o..

      £64.58 (£77.50 inc VAT)

      show quantity discounts
      other widths
      6mm Expansion Joint Profile PVC - length 2.5m (pack of 3).

      6mm Expansion Joint Profile PVC - length 2.5m (pack of 3).

      3035- Free Delivery  show quantity discountsDelivery Time: 1 - 2 days

      £90.86 (£109.03 inc VAT)

      show quantity discounts

      6mm Expantion Joint Profile with soft PVC centre section for insulation systems, with alkali-resistant glassfibre mesh. Movement: +/-5mm. This profile is recommended for vertical use only. ..

      £90.86 (£109.03 inc VAT)

      show quantity discounts
      6mm Expansion Joint Profile PVC- CORNER - length 2.5m (pack of 3).

      6mm Expansion Joint Profile PVC- CORNER - length 2.5m (pack of 3).

      3036- Free Delivery  show quantity discountsDelivery Time: 1 - 2 days

      £90.86 (£109.03 inc VAT)

      show quantity discounts

      6mm Expantion Corner Joint Profile with soft PVC centre section for insulation systems, with alkali-resistant glassfibre mesh. Movement: +/-5mm. This profile is recommended for vertical use only. ..

      £90.86 (£109.03 inc VAT)

      show quantity discounts
      6mm PVC Base Profile - length 2m (pack of 15)

      6mm PVC Base Profile - length 2m (pack of 15)

      37500 - Free Delivery   Delivery Time: 1 - 2 days

      Guide Price: £196.63 (£235.96 inc VAT)

      6mm PVC base profile for use between DPC and insulation systems. Available in a range of widths and render thicknesses. Can also be used in conjunction with a PVC angle section as a 2 part  base starter track. Please contact us for details...

      Guide Price: £196.63 (£235.96 inc VAT)

      other thicknesses
      6mm Mesh Wing PVC Window Frameseal Beads (pack of 30).

      6mm Mesh Wing PVC Window Frameseal Beads (pack of 30).

      37806 - Free Delivery  Delivery Time: 2 - 3 days

      6mm self adhesive PVC profile for use on window reveals or door frames. Attached to the frame with a foam tape, the frameseal has an adhesive strip to enable use of a protective film to be applied during the rendering process, which is snapped off on completion...

      other sizes
      9mm Cembrit PB Permabase Cement Board - Base Board for External Render

      9mm Cembrit PB Permabase Cement Board - Base Board for External Render

      2400x1200 - 2.88m2  Delivery Time: 1 - 2 days

      Guide Price: £36.56 (£43.87 inc VAT)

      £12.69/m2 (£15.23/m2 inc VAT)

      9mm Cembrit Permabase is a rigid cement and aggregate board incorporating polystyrene beads. The board's flat surface is strengthened with glass mesh. Its reinforced tapered edges designed to facilitate invisible butt joint installation. Cembrit PB cement board is lightweight, water resistant, so is..

      Guide Price: £36.56 (£43.87 inc VAT)

      £12.69/m2 (£15.23/m2 inc VAT)

      = m2
      other thicknesses
      Ceresit CR65 Waterproofing (Tanking) Slurry

      Ceresit CR65 Waterproofing (Tanking) Slurry

      CR65  show quantity discountsDelivery Time: 5 - 7 days

      £35.99 (£43.19 inc VAT)

      show quantity discounts

      Ceresit CR65 is a high water impermeable tanking slurry, which permits diffusion, but is frost resistant, and suitable for drinking water tanks. Used on the horizontal and vertical surfaces of buildings, structural components and tanks, for waterproofing against water loads, for waterproofing m..

      £35.99 (£43.19 inc VAT)

      show quantity discounts
      Ceresit CT48 Silicone Paint (15 litres)

      Ceresit CT48 Silicone Paint (15 litres)

      CT48 - 15l  Delivery Time: 2 - 3 days

      Guide Price: £78.00 (£93.60 inc VAT)

      £1.56/m2 (£1.87/m2 inc VAT)

      Ceresit CT 48 Silicone Paint is used for protecting facades, concrete constructions, interiors. It can be applied on the mineral substrates such as concrete, cement plasters, lime-cement plasters and lime plasters that have never been painted before. This paint can be used for painting mineral plast..

      Guide Price: £78.00 (£93.60 inc VAT)

      £1.56/m2 (£1.87/m2 inc VAT)

      = m2
      Ceresit CT77 Mosaic Render grain 1.2mm - 1.8mm

      Ceresit CT77 Mosaic Render grain 1.2mm - 1.8mm

      CT77  show quantity discountsDelivery Time: 5 - 7 days

      £69.00 (£82.80 inc VAT)

      £12.55/m2 (£15.06/m2 inc VAT)

      show quantity discounts

      1.2mm - 1.8mm grain Ceresit CT 77 Mosaic Render is used for applying decorative colourful plasters to traditional plasters, concrete substrates, gypsum substrates and chipboards, gypsum cardboards, etc. Transparent resins are the binder and coloured quartz gravels size of 1.2 mm - 1.8 mm and natural..

      £69.00 (£82.80 inc VAT)

      £12.55/m2 (£15.06/m2 inc VAT)

      show quantity discounts
      = m2
      Custom Cut Oversill and Window Sill Flashing (with full end caps-pair) width from 30mm to 200mm - length up to 2.5m

      Custom Cut Oversill and Window Sill Flashing (with full end caps-pair) width from 30mm to 200mm - length up to 2.5m

      WEC 761 30-200mm - Free Delivery  Delivery Time: 3 - 5 days

      Guide Price: £36.75 (£44.10 inc VAT)

      Our custom-cut Aluminium oversill and window sill flashings are durable, low maintenance quality beads for external wall insulation, suitable for most weather conditions and custom made to fit any project requirement. In order of protecting the section during transportation and fixing, extensions ar..

      Guide Price: £36.75 (£44.10 inc VAT)

      Finishing Float For Insulated Textured Renders - Plastic.

      Finishing Float For Insulated Textured Renders - Plastic.

      14cm x 28cm - free delivery  show quantity discountsDelivery Time: 1 - 2 days

      £16.50 (£19.80 inc VAT)

      show quantity discounts

      Plastic trowels are used in finishing of the insulated textured renders - silicone, acrylic or silicate.CHARACTERISTICS:plastic handlelightweight and sturdysize: 14cm/28cm..

      £16.50 (£19.80 inc VAT)

      show quantity discounts
      Finishing Float For Rendering - Stainless Steel.

      Finishing Float For Rendering - Stainless Steel.

      13cm/25cm  show quantity discountsDelivery Time: 1 - 2 days

      £16.50 (£19.80 inc VAT)

      show quantity discounts

      Finishing trowels are used in smoothing and finishing the surface of concrete or plaster.  They help to compact the surface and add to the quality and durability of work. They are crafted from the highest quality materials using the best design standards.CHARACTERISTICS:plastic handlelightweigh..

      £16.50 (£19.80 inc VAT)

      show quantity discounts
      ISO RG Insulation Washer for Soft Panels

      ISO RG Insulation Washer for Soft Panels

      ISO RG Soft  Delivery Time: 3 - 4 days

      ISO RG Insulation Washer for Soft Panels is used for fixing soft insulation panels.  ..

      ISO RG Screw Cover Cap Insulation Washer (pack of 100).

      ISO RG Screw Cover Cap Insulation Washer (pack of 100).

      ISO RG -61928060000 - Free Delivery  show quantity discountsDelivery Time: 1 - 2 days

      £25.51 (£30.61 inc VAT)

      show quantity discounts

      Polypropylene ISO RG Screw Cover Cap Insulation Washer is used for fixing insulation panels and it has no thermal transmission due to the screw cover cap. Can be used with screws up to 6mm in diameter...

      £25.51 (£30.61 inc VAT)

      show quantity discounts
      12.5mm Knauf Aquapanel Exterior Cement Board

      12.5mm Knauf Aquapanel Exterior Cement Board

      2400x900mm - 2.16m2  show quantity discountsDelivery Time: 1 - 2 days

      £36.82 (£44.18 inc VAT)

      £17.05/m2 (£20.46/m2 inc VAT)

      show quantity discounts

      12.5mm Knauf Aquapanel Exterior Cement Board provides a solid, dry base that can withstand the extreme weathering effects of wind, rain and snow. It is an ideal substrate for directly applied render finishes and can be used for exterior walls in ventilated systems,exterior ceilings and soffits. Once..

      £36.82 (£44.18 inc VAT)

      £17.05/m2 (£20.46/m2 inc VAT)

      show quantity discounts
      = m2
      Knauf Aquapanel Exterior Joint Tape

      Knauf Aquapanel Exterior Joint Tape

      100mm x 50m  Delivery Time: 2 - 3 days

      £31.35 (£37.62 inc VAT)

      Aquapanel Exterior Joint Tape is a 100mm wide, glass fibre tape with an alkaline resistant coating. It is embedded into Aquapanel Exterior Joint Filler to reinforce exterior joints as part of the Aquapanel Exterior System.INSTALLATIONAquapanel Cement Boards must be dry, clean and dust-free and ..

      £31.35 (£37.62 inc VAT)

      Knauf Aquapanel Exterior Reinforcing Mesh

      Knauf Aquapanel Exterior Reinforcing Mesh

      1000mm x 50m  Delivery Time: 2 - 3 days

      £195.31 (£234.37 inc VAT)

      £3.91/m2 (£4.69/m2 inc VAT)

      Knauf Aquapanel Exterior Reinforcing Mesh is a wide glass fabric mesh designed to resist sliding. It is manufactured from glass filament fibres with a nominal diameter of <5m. It is used to reinforce Aquapanel Exterior Basecoat and Aquapanel Joint Filler.INSTALLATIONApply Aquapanel Exterior ..

      £195.31 (£234.37 inc VAT)

      £3.91/m2 (£4.69/m2 inc VAT)

      = m2
      Knauf Aquapanel Exterior Reinforcing Tape

      Knauf Aquapanel Exterior Reinforcing Tape

      200mm x 50m  Delivery Time: 1 - 2 days

      Knauf Aquapanel Exterior Reinforcing Tape is used to reinforce joints in exterior walls where a coat of paint instead of render finish is to be applied on the Aquapanel Exterior Basecoat.INSTALLATIONApply Aquapanel Joint Filler over the joints and embed Aquapanel Exterior Reinforcing Tape.CERTIFICAT..

      Knauf Aquapanel Interior Joint Tape

      Knauf Aquapanel Interior Joint Tape

      100mm x 50m  Delivery Time: 1 - 2 days

      Aquapanel Interior Joint Tape is a 100mm wide, glass fibre tape with an alkaline resistant coatingfor use where Aquapanel Interior Panel is to be jointed using tile adhesive.CERTIFICATIONManufactured in the UK to EN 520, BS 1191 and BS EN ISO 9000 using advanced production facilities,ISO 14001 certi..

      Knauf Aquapanel Joint Adhesive (PU) - 310ml

      Knauf Aquapanel Joint Adhesive (PU) - 310ml

      310ml  Delivery Time: 2 - 3 days

      £7.20 (£8.64 inc VAT)

      Aquapanel Joint Adhesive (PU) is used for wall applications to bond individual Aquapanel Interior Cement Board to a wall without the need for labour intensive coating or inserting a joint strip.INSTALLATIONEnsure that the edges are cleaned using a wet brush, Apply a continuous linear bead of Aquapan..

      £7.20 (£8.64 inc VAT)

      Knauf Aquapanel Maxi Screws SN39 - box of 500

      Knauf Aquapanel Maxi Screws SN39 - box of 500

      39mm  Delivery Time: 1 - 2 days

      £22.98 (£27.58 inc VAT)

      Aquapanel Maxi SN39 needlepoint screws have been specially developed for fixing Aquapanel Cement Board on to timber and metal frameworks of differing thicknesses. Aquapanel Maxi Screws SN39 can be used for both wall and ceiling applications in interior and exterior applications. Aquapanel Maxi ..

      £22.98 (£27.58 inc VAT)

      Knauf Aquapanel Rustproofed Screws SN40 - box of 250

      Knauf Aquapanel Rustproofed Screws SN40 - box of 250

      40mm  Delivery Time: 1 - 2 days

      £30.98 (£37.18 inc VAT)

      Knauf Aquapanel Rustproofed Screws SN40 has been specially developed for fixing Aquapanel Exterior Cement Board to timber substructures. These needlepoint screws are made from V2A stainless steel. The screws also have milled ribs to the edge of the screw head that ensures that they can be screw..

      £30.98 (£37.18 inc VAT)

      90x110mm Mesh Wing PVC Corner Profile 50m Roll.

      90x110mm Mesh Wing PVC Corner Profile 50m Roll.

      3752 - Free Delivery  show quantity discountsDelivery Time: 1 - 2 days

      £86.99 (£104.39 inc VAT)

      show quantity discounts

      50m roll of PVC Corner profile with alkali resistant glass fibre mesh wings 90mm x 110mm, which allows it to be cut to the required length and reduces waste. Can be folded to any angle...

      £86.99 (£104.39 inc VAT)

      show quantity discounts
      Showing 31 to 60 of 191 (7 Pages)